GUARDIAN GRC-38non-acid radiator cleaner that removes

Description : 

GRC-38 is a non-acid radiator cleaner that removes

rust and scale, and emulsifies oil and grease from engine radiators /

cooling systems.

Applications : 

GRC-38 is widely used in the radiators and cooling

system of engines commonly found in automotives, generators,

tractors, excavators etc.

Advantages :

• Non-acid formula. GRC-38 dissolves rust, corrosion and scale without harming steel, iron, aluminium or copper. It is not corrosive to the skin, and is safe and effective.
• Descales and cleans in one operation. GRC-38 emulsifies oily contaminants in the cooling system that cause foam and harm to seals. Foam is an insulator and reduces cooling efficiency. With GRC-38, the entire system is descaled, rinsed, and cleaned in one operation.
• Fast action. GRC-38 equires only 15 – 20 minutes to clean the cooling system once the engine reaches its operating temperature.
• Cost effective. For the average automobile, only 1 litre of GRC-38 is required for effective treatment, and with the yearly G-COOL change, keeps the system in top cooling efficiency. A very cost effective solution for maximum operating efficiency.

Instructions :

1. Ensure engine is off and cooled before draining the radiator of all its content.
2. Add 75% clean water and 25% GRC-38 to system to be treated. E.g. for a 4 litre radiator, add 3 litres of clean water with 1 litre of GRC-38 to fill the radiator.
3. Replace the radiator cap but do not tighten.
4. Run engine until hot and then run for another 15 minutes.
5. Stop engine and drain system. If solution is hot, allow to cool before draining.
6. Refill radiator with running water and leaving drain tap open, run the engine to provide continuous flushing.
7. When clear water is observed from the drain tap, stop and fully drain the system.
8. Check the system capacity and refill using about 50% water and 50% G-COOL protective coolant.

Properties :

TYPE                       : Non-Acid Radiator Cleaner.

ODOR                      : None.

FLAMMABILITY     : Non-Flammable.

TOXICITY               : Harmful If Swallowed.

pH FACTOR             : 6.5 – 7.5

BOILING POINT      : 93⁰C (Atmospheric pressure)

SPECIFIC GRAVITY : 1.02 (Water = 1.0)

COMPOSITION        : Proprietary penetrants and emulsifiers.

GUARDIAN G-COOL.water cooled engines

Description : 

G-COOL. is a propylene glycol based engine coolant that provides protection against freezing and boiling and also against corrosion.

Applications :

 G-COOL.is ideal for use in all water cooled engines, automobiles, cranes, trucks,
generators, compressors etc.

Advantages :

• Corrosion and Rust Inhibition. G-COOL. contains polyphase corrosion inhibition additives that prevent rust and corrosion, and protect copper, aluminium and iron parts. No need for other boosters or additives.
• Increases Cooling Efficiency. Modern engines running at high temperatures may boil away water causing severe damage. G-COOL. raises the boiling point of water and prevents clogging deposits to increase cooling efficiency.
• Decrease Freezing Point. G-COOL. contains proplylene glycol which decreases freezing point
• Save you time and money. Using G-COOL. means extended engine life, increased reliability, and lower maintenance and repair costs.
• Safe. Proplylene glycol based formulation is proven safe.

Instructions :

1. Use GRC-38 to flush cooling system thoroughly before using G-COOL.
2. Determine the system capacity
3. Close the drain tightly and add 40% - 60% of the tank capacity with G-COOL  Fill remaining tank capacity with clean water.
4. For full protection, flush the system and replace the G-COOL once a year.

Note : fill the overflow tank, if any with 50:50 G-COOL and clean water.

* A system under pressure can handle higher temperatures, and offers a higher static boiling point. Every pound of pressure exerted on G-COOL  the static boiling point of G-COOL increases by approximately 1.7°C. At atmospheric pressure (760 mmHG), 50/50 G-COOL mix with water raises the fluid boiling point to 109°C

GUARDIAN MOTOR-ON solvent emulsifier.

Description :

MOTOR-ON is a heavy-duty degreaser for engines, tools, machinery and floors.

Applications : 

MOTOR-ON is a powerful and effective way to remove heavy impacted grease and oil deposits from engines in cars, trucks, boats and machinery.

Advantages :

• Fast acting. MOTOR-ON cuts through grease and grime on engines, tools, machinery and floors thus saving time and labor.
• Versatile. MOTOR-ON can be safely used on plastics, rubber, paint and most other surfaces.
• Easy application. With MOTOR-ON  just apply and hose off. There is no need for special and expensive equipment.
• Safe to use. MOTOR-ON is non-caustic, non-alkaline and does not emit toxic fumes. Harmless to metal, painted surfaces and normal skin.
• Economical. MOTOR-ON can be diluted up to 10 times without losing its effectiveness.
• Environmental friendly. MOTOR-ON aerosol packing is CFC-free.

Instructions :

Engine and chassis cleaning. For average work, mix MOTOR-ON with 8 parts of mineral spirits or
kerosene. For light cleaning, mix 1 to 10 parts. For heavy cleaning mix 1 to 5 parts. Spray or brush
mixture over equipment to be cleaned. If dirt is heavily encrusted, use a stiff brush to work on surface. Let soak for 10 to 15 minutes for complete penetration, then flush thoroughly (with water, if applicable).

Dip tank cleaning. Mix MOTOR-ON to 8 parts kerosene in the tank. Soak parts in the tank for 30 minutes to 2 hours as necessary. After cleaning, flush thoroughly (with water, if applicable).

Industrial equipment and machinery cleaning. For average conditions, mix MOTOR-ON with 8 parts of kerosene or mineral spirit. For light cleaning, mix 1 part to 20 - 30 parts of water. For heavy build-up, 1 part to 6 parts water. Use warm water for better effectiveness. Spray or brush mixture over equipment to be cleaned. Use a soft brush on areas where dirt is heavily encrusted. 
Let soak for 15 to 20 minutes, then flush thoroughly (with water, if applicable).

Cars, trucks, and buses washing. Use one part MOTOR-ON to six parts kerosene for heavily encrusted areas. Can be applied by spraying or use of long handled, soft brush. Then rinse off with water.

To remove oil stains from concrete floor. Mix 1 part MOTOR-ON to 8 parts kerosene. Brush into areas stained. Stand for 5 mins, rinse off with water.

Properties :

TYPE                   : Solvent emulsifier.
FLAMMABILITY : Combustible.
TOXICITY           : Harmful, may be fatal if swallowed.
COMPOSITION   : Biodegradable emulsifiers, penetrants, aliphatic solvents and terpenes.